Home / Programming / StickyMat System – DWM

What system works best with vinyl flooring?

Warmup recommends using the DWM heating mat or DCM-PRO heating system under vinyl flooring. Leveler must be used over the system before vinyl installation.

Watch a 90 second time-lapse of a heated vinyl floor installation and subscribe to our YouTube channel for more radiant heating content:

Further Questions?

Miscellaneous questions

- What self-leveler should I use?

- Can I install two thermostats on a single 240V circuit, with one controlling a bathroom mat and the other controlling a separate two mats?

- Why is my Floor not Reaching Target Temperature?

- Why does my thermostat trip every time it reaches the same temperature?

- Why does my floor heat unevenly?

- Why does my floor get warmer in some spots?

- When my screen goes dark, will my floor continue to heat?

- When I push the test monthly button on my thermostat, the screen goes red and tells me to call Warmup. Should I be worried?

- The Factory Joint Rule

- How can I turn my system on or off completely?

- Does the 3iE have a battery backup?

- Can I replace tile immediately when repair is completed?

- Can I use an uncoupling membrane with the NADWS cable ?

- Can I install my Warmup system directly on top of plywood?

- Can I connect one Warmup heater to another in series?

- Can I connect more than one Warmup heater to a thermostat?

- Can a wooden floating floor be installed directly over the Warmup NADWS system?

- At what temperature does the CIT-1 sensor activate?

- What type of thinset should I use with my Warmup system?

- How Long will my Electric Floor Heating System Take to Heat Up?

- Do I choose cable or mat electric floor heating systems?

- Can I Cut the Electric Floor Heating System Wire if I Have too Much?

- Can I cut my floor heating mat if it’s too large?

- Why does my heater have a ground wire but the thermostat has no terminal for ground?

- What is the EMF level of Warmup cables?

- Should I use a 120V or 240V electric floor heating system?

- Can I upgrade to the 6iE?

- How much accumulation can a snow melting system handle?

- Can I use area rugs with underfloor heating?

- What are the differences between the old WSM version (before 2020) and the new?

- Can I reset my password?

- What is an uncoupling system?

- How much does underfloor heating cost to operate?

- What does the DCM-PRO Warranty Cover?

- Will the membrane keep it’s decoupling capability over time?

- Will the peel-and-stick glue ever dry?

- Does Warmup Underfloor Heating Comply with Title 24?

- What Does the Error Message on my Tempo Mean?

- How do I test my system using a Megger (Mega-Ohmmeter)?

- Can I Install my Floor Heat over an Existing Sheet of Vinyl Floor?

- Programming the Floor Temperature

- Initial Set up of the 3iE Energy Monitoring Floor Heating Thermostat

- My sensor triggers properly most of the time but seems to miss very wet snow.

Preparing for your project

- Can I install two thermostats on a single 240V circuit, with one controlling a bathroom mat and the other controlling a separate two mats?

- Can sheet vinyl be used on top electric under floor heat?

- What type of thinset should I use with my Warmup system?

- What do I need to prepare for my electric floor heating project?

- How Long will my Electric Floor Heating System Take to Heat Up?

- Do I choose cable or mat electric floor heating systems?

- Was your electric floor heating system installed directly on a concrete slab?

- Should I use Self-leveler or Thinset ?

- Floor Probe Installation Instructions

- What are the electrical requirements for my Warmup system?

- How much accumulation can a snow melting system handle?

- Can I install floor heat under my tub?

- Do Warmup thermostats zone?

- Does every room with floor heat need its own thermostat?

- What product do I use if I need 110V?

- Can floor heating be used as a primary heat source?