DCM-PRO Cable

Both deliver 13.1 W/sq ft. Learn when to choose 120V or 240V electric floor heating, how room size decides, and whether 110V is the same as 120V.

Learn electric floor heating layout considerations, including cable spacing, wall and fixture clearances, furniture placement, and common installation mistakes to avoid.

Compare heating cable vs. heating mat for electric floor heating. Learn the differences in installation, cost, heat output, flexibility, and flooring compatibility to choose the right system.

Learn everything you need to know about installing underfloor radiant heating in a shower floor.

Learn when to use thinset or self-leveler for electric underfloor heating. Compare flooring compatibility, DCM-PRO requirements, primer, curing times, and installation best practices.

Learn which flooring works best with electric underfloor heating. Compare tile, vinyl, wood, laminate, carpet, and concrete installations, recommended heating systems, temperature limits, and installation requirements.

Yes, radiant heat can be used as a primary heat source. Learn how to calculate heat loss, convert watts to BTUs, and confirm radiant floor heating can heat your room on its own.

The only way to see if the cable is going to work and is not damaged is to use an ohmmeter to check the resistance between the heating conductors matches what it should be in…

Are you installing the DCM-PRO cable without the DCM-PRO membrane? You will need fixing strips. This post tells you how many for each cable size.

Are you wondering how long after installation you have to wait to begin using your floor heating system? Learn all about wait time in this post.

If you are finalizing a Warmup installation it is almost time to register your warranty! Find the link here to the warranty registration page.

Are you getting ready to install the DCM-PRO system? Check out this video for helpful tips and tricks for getting the job done right.

Warmup recommends testing your underfloor heating cables before, during, and after installation. Follow along with this post for support.

If you are installing the DCM-PRO cable in your home you may be wondering about the diameter of the cable? Find this information and more here.

Each row in the membrane is referred to as a peg. Learn more here about minimum cable spacing to ensure a proper install of your DCM-PRO system.

When installing sheets of Warmup membrane, you should try your best to install with no overlapping or large gaps.

This page explains how to determine which voltage to run to your DCM-PRO heating system.

Outlined description of when to test your DCM-PRO cable and why you should do it.

This page outlines the recommended installation methods for your installing your sensor probe.

This page explains the positioning of the factory joint to ensure a successful installation of your Warmup heating system.

The conductor cores and ground braid of the 10' cold lead are factory joined in a water resistant joint assembly to each supply conductor and ground conductor of the unheated lead.

The cold tail lead and the sensor probe should be run in separate conduits. This will prevent any interference from the cold tail lead affecting the temperature readings from the sensor probe.

This page explains the DCM-PRO spacing guidelines and recommendations.

This page explains how to extend your lead wire or connect your heater to a thermostat in a remote location.

This page will give you pointers about trimming your cold lead to fit easier in the conduit and electrical box.

It depends on a lot of factors, but a classic installation over ¾” plywood with NADWM mats would take about 30 minutes to heat from 60F to 80F. Click "Read More" for details. 

Uncoupling systems are becoming increasingly popular. Learn more here about what an uncoupling system is here so that you can see if it's suitable for you.

If you are considering an underfloor heating system you can read more here about running costs.

We stand behind our products. Learn more about how we'll be there if something happens with your system down the road.

If you are considering the DCM-PRO system or if you already have it in your home you may be wondering how long it will keep its uncoupling capabilities. Learn more here.

This page describes the composition of the DCM-PRO cable and the different components that make up this heating system.

If you are planning a floor heating project with the DCM-PRO system you may be curious about product thickness. Ge tthe quick answers you need here.

Learn more about the basics of how underfloor heating works.

Learn how to repair a damaged heating mat or loose wire system with our step-by-step guide. This article provides detailed instructions to help you restore your underfloor heating system quickly and safely.

Are you looking for troubleshooting support at your home? We are here to help online and by phone 24 hours, 7 days a week.

Are you experiencing uncertainty with your underfloor heating and looking to get answers? An infrared thermal camera may be the tool you need.

To ensure that the floor heating system will function properly, always check the resistance readings of the wires with a digital multimeter before, during, and after installation. Continue reading to learn how.