Warmup® Underfloor Heating was snapped up for 300 bathrooms in Gibraltar’s largest development.

The developer approached Warmup after a trade show in the UK and proceeded with an order for Warmup® Undertile Heating Mats with accompanying heating controls, the TSTAT thermostats.

At least two more towers are waiting in the pipelines to be installed with yet more Warmup® systems before the year is up.

When completed, Ocean Village will be the biggest residential and leisure centre in Gibraltar. It will boast exclusive waterside living and premium commercial and recreational facilities. 

When a middle aged couple there decided to build their dream house using their life savings, they were advised by some American and German entrepreneurs involved in wind turbines to install Warmup® Underfloor Heating for increased comfort and to resolve the humidity issue.

The cautious pair sought additional opinions and it was only after further research that they ventured out of the island for the first time ever, to visit a retailer in San Miguel whom they’d located online.  A close examination of the product later and impressed by plenty of excellent feedback, they took the plunge.

They chose Warmup® Underfloor Heating Mats for rapid installation and 5 of the exclusive Warmup® XStat Thermostat for its user-friendliness and clever functions including self learning capabilities to ensure the right temperature at the right time.  To enable individual control and improved heating efficiency, each room was fitted with its own thermostat, which comes with a floor sensor each for more accurate temperature readings.

The systems were installed quickly and the couple is thrilled with their warm tiled floors, not to mention the marked improvement in the humidity condition!

Prevention is better than cure.  With installation, following the instructions carefully can eliminate most after-sales problems.  Although systems in the market might seem similar and you already have relevant prior experience, always read through the manual thoroughly to preempt avoidable mistakes.  Planning your installation ahead will allow for a clearer idea of the steps involved and increase your chances of a smooth progress.  And at any time you have a question, call the manufacturer to be sure.
 

Mind the subfloor.  When installing, there are some things you can look out for to reduce the likelihood of complications.  For a start, make sure the subfloor is clean before laying the heaters over the area to be heated.  This helps the adhesives to attach far more easily.  Check too, if the subfloor material requires priming or not.  On bases such as insulation boards, that coat of primer might never dry.
 

Test, Test, Test!  After fitting the floor sensor probe, test both the heater and the floor sensor.  Heating cable can be stressed by incorrect installation or damage but the fault may not show up straight away.  By taking and recording resistance readings before, during and after installation, or as shown in the instructions, it makes a quick job of identifying the point of damage at a later date.  Alternatively you may use special gadgets that warn you right at the point of accident.  Warmup has a Watchdog monitor which is temporarily connected to the heating mat until the tiling is completed.  If the wire is broken or damaged, an alarm sounds.  In such instances, repair kits should be available from the heating company.
 

Be grout-smart. When tiling, it is advisable to choose flexible adhesive and grout, for this will be more accommodating towards the expansion and contraction effects of heating on objects, in this case, the tiles.  If it’s a tight turnaround time, consider using rapid-set types.  Once again, check with the manufacturer if in doubt.
 

Play by the rules.  For making electrical provisions, installing and connecting the thermostat, it is obligatory to hire a Part P qualified electrician in accordance with British Regulations.  So remember to coordinate this one.
 

Invest in a good system for it is less likely to create post-installation problems.  The most common worries tradesmen have are the hassles of a failed system and the potential need to lift entire floors.  Choosing a reliable manufacturer however, could relieve at least part of the stress.

A fair indication of a product’s quality is if it’s approved by a control body that tests the electrical strengths and safety levels.  In Britain, BEAB (British Electrotechnical Approvals Board) is the trusted authority on this.  Other features to look out for include warranties and after-sales support.  Manufacturers are not likely to promise product life-spans and services that they are not confident of delivering, so non-technical benefits can serve as a gauge too.  Currently in the market, warranties range from an average of 10 years up to a lifetime.  Warmup for example, goes a step further with their SafetyNet™ Guarantee which insures you against installation mishaps.  Should you damage the wires accidentally prior to tiling, Warmup will replace the heater at no extra charge.  Details can be found on warmup.com 

Also check that you’ll be able to contact the heating company easily for backup.  A helpline, especially if it’s round the clock, is invaluable.  As an installer, it is always useful to know you have somewhere to go should you encounter a situation on a job, and better yet if there are service engineers to literally lend a hand and minimise disruption.  The fewer tiles lifted, the lower the costs incurred!
Finally, with new products being introduced constantly, do ask for refresher training sessions with your preferred supplier if they are not already offered.

All the bathrooms in this prestigious new harbourfront development will have Warmup® mats installed under the tiled floors and operated by the Warmup® MStat, a user friendly thermostatic heating control. To optimise heating efficiency, the mats will be laid onto Warmup® Insulation Boards to reflect heat back up through the tiles, minimising unnecessary heat loss. When the cold does eventually set in during winter, the homeowners can still be pampered with warm floors underfoot, a benefit that ups the wow factor of each apartment, rendering it a powerfully persuasive selling tool of the development.

B. Solis Constructora’s decision to use Warmup was attributed to the quick and simple installation of the systems, crucially reducing the risks of costly delays to the construction. The accessibility to local Warmup fitters increased the practicality of the process while the ongoing personalised service received from the Warmup sales team from day 1 enabled them to enjoy reassurance and peace of mind, enhancing the entire customer experience.

Warmup’s commitment to excellence in both quality and service echoes the corporate values of B. Solis Constructora, fostering a mutual trust and laying a solid foundation to the working relationship. Underway since June 2005, the project as a whole is scheduled for completion over just 28 months, in time for summer 2008.

Now you can step out from the hottest of baths and check your reflection out right away with the latest offering from award-winning Warmup.

The all-new Warmup® Mirror Demisters are a technologically advanced, permanent, safe and simple solution for steamed up mirrors – ideal in the bathroom!

Installation cannot be simpler – Just stick the flat self-adhesive film directly onto the back of the mirror and voila, it’s done.

This device also connects to existing room light circuit for automatic operation when light is switched on.  Nifty!

Suitable with most types of mirrors, existing or newly installed, the demister can also be used in combination for larger areas.

The Warmup® Mirror Demisters feature resistance to moisture, vibration, shock, dust and ageing and come with a one-year warranty. 

G Wood Worcestershire

Thank you too Mrs Wood, for the fantastic feedback and continued support.  May you enjoy many more years of comfort with Warmup!

Using state–of-the-art technology, the new Warmup® Carbon Heaters are perfect for heating laminate, wood, carpeted and even certain vinyl floors in dry areas such as lounges or bedrooms.
With this self-regulating system, the warmer the element gets, the lower the energy draw.  So not only does it not warp or overheat, it is brilliantly energy-efficient.
 

Typical of Warmup® products, the carbon heater is so flat that it will not affect floor levels at all and installation is as simple as rolling the heater out.
The carbon heater is available in two widths of 300mm and 900mm which are easily combined for maximum heating coverage.
Warmup’s free quote and layout service takes the hassle away from you and as a customer, enjoy a 30-year warranty on the Warmup® Carbon Heater plus unlimited access to our 24/7/365 technical helpline.

Our latest version of the Warmup® Ribbon Heaters comes with a built-in Earth Screen, making installations in wet areas both quicker and safer than ever.� No need to install additional grounding nets or self-levelling compound - simply roll the heater out!

At barely 2mm, the ultra-thin heating ribbon won’t raise floor levels. It is available in 2 widths of 0.5m and 1m, making it easy to combine heaters for maximum coverage.

The Warmup® Earthed Ribbon Underlaminate Heater is compatible with floor finishes such as laminate, engineered wood, vinyl and carpet.

Customers enjoy a 15-year warranty and access to our 24/7/365 technical helpline.

The temperature of the floor is regulated by the Warmup XSTAT thermostat. The Warmup 200w heating mats are suitable for floor finishes such as ceramic tiles, stone and slate.

More information.

Customers enjoy 10-year warranty, SafetyNet™ Installation Guarantee and 24/7/365 technical helpline.